Egress Window Wells in Rochester, MN

Free on-site quote with every line item listed.


Egress Windows Rochester MN digs, sets and replaces egress window wells across Rochester and Olmsted County.


$1,200 to $4,200 per well. Most jobs land near the $2,200 average.


Permit on every job. Since May 1, 2025, Rochester requires a permit for every residential window replacement.


9 sq ft, 36 inches out. The well gives the window room to open and you room to climb.


Steps or a ladder past 44 inches. Built in or bolted on, it has to reach the open window.

Request a Free Quote

Free quote. No obligation. No pressure.

Window Well Materials Compared

Stone steps like the tiered steps in a deep window well

Galvanized Steel Wells: $800 to $1,800

The workhorse. Corrugated steel bolts to the foundation and holds back backfill. Rust and frost heave are what wear it out.

Rochester home in winter snow

Composite and Fiberglass Wells: $1,000 to $2,200

Molded wells with tiered steps cast in. On many models the steps meet the exit rule for a deep well.

Small basement window set in a brick foundation

Clear Plastic Wells: $700 to $1,000

Pulls daylight down to the basement window. Best for shallow wells that need no ladder.

Rusted metal like an old steel window well

Custom Concrete or Block Wells: $1,500 to $2,800

A permanent wall for oversized or terraced wells. The highest cost of the four.

Window Well Covers in Rochester, MN

Rochester averages about 53 inches of snow a year. An open well fills with it. Minnesota code requires an egress cover to open from inside with no key, no tool and no special knowledge. Rochester inspectors check for an easily removable cover.

Frost-covered grass in early winter

Clear Plastic Window Well Covers: $70 to $200

The entry option. It keeps out leaves, rain and small animals and lets daylight into the basement. Best for wells outside foot traffic.

A vehicle buried in deep Minnesota snow

Polycarbonate Window Well Covers: $200 to $300

Heavier clear panels built for snow load. Light still reaches the room, and the cover lifts open from inside.

Close-up of a wall of metal bars

Steel Grate Window Well Covers: $300 to $700

Welded steel bars stop falls into deep wells. Air moves through. Snow and rain do too, so we check the well drain before we set one.

A round hole dug into the ground

Custom-Fit Window Well Covers: $500 to $1,000

Made for oversized, terraced and odd-shaped wells. We test the cover from inside the basement before the job closes.

How We Set a Rochester Window Well

Step 1: Locate and Measure

We call Gopher State One Call to mark buried lines, then measure the sill depth and size the well to the open window.

Step 2: Excavate and Anchor

We dig below the sill, set the well tight to the foundation and bolt it in place. The well runs at least 8 inches past each side of the window.

Step 3: Drain Rock and Grade

Drain rock goes in the bottom so water moves down and away from the glass. We slope the soil around the well away from the house.

Step 4: Exit, Cover and Inspection

We add a ladder or steps to any well over 44 inches deep, fit the cover and book the City of Rochester inspection.

Why Choose Egress Windows Rochester MN

Rental-Ready

Basement Bedrooms

Rochester's rental code calls for 820 square inches of open area, a 44-inch sill and a ladder in wells 44 inches deep or deeper. We build to those numbers.

Permits Filed With Rochester Building Safety

We submit the permit through Accela Citizen Access, book the inspection and hand you the closed permit.

Covers Tested From Below

Code R310.4 says a cover must open from inside by hand. We push each cover open from the well before we leave.

Rochester Window Well FAQs

What does an egress window well cost in Rochester?

Window wells run $1,200 to $4,200, with most jobs at $1,800 to $3,000 and a $2,200 average. Labor alone runs $900 to $1,500.

Do I need a permit for a window well in Rochester?

Yes. Since May 1, 2025, the City of Rochester requires a building permit and inspections for every residential window replacement. A new foundation opening needs one too. We file it through Accela Citizen Access.

How deep can a window well be before it needs a ladder?

A well over 44 inches deep needs a permanent ladder or steps (R310.2.3.1). Rungs must be at least 12 inches wide, sit 3 inches off the wall and stand no more than 18 inches apart.

What size does an egress window well have to be?

At least 9 square feet of floor area with at least 36 inches in each direction (R310.2.3). The window must open all the way inside the well.

What window well cover works in a Rochester winter?

A polycarbonate cover at $200 to $300 keeps snow out and lets light in. A metal grate at $300 to $700 holds weight. Plastic runs $70 to $200. All must open from inside by hand (R310.4).

Why is my old window well pulling away from the house?

Rust, frost heave and backfill pressure bend old steel wells off the wall. Replace it rather than patch it. A straight swap can run as little as $500 in labor.

A well built for Minnesota winters

and a clean way out.